Installing Win95 on a Javelin2

Last edited: December 15, 2003 08:20 AM

Win95 Installation Procedure

  1. Plug in standard floppy drive using installed Javelin Floppy Disk Cable.
  2. Insert WIN ’95 ‘setup’ disk
  3. Turn on system and press to enter System BIOS.
  4.
  5. change Internal Cache to ‘WriteBack’
  6. make sure Config-1 is set
  7. You will boot into WIN ’95 setup. Do a typical WIN ’95 installation.

Configuring the Network Adaptor

  1. Goto Control Panel – System – Device Manager – Network Adapters – NE2000 Compatible
  2. Press – Properties – Resources
  3. ; deselect ‘Use Automatic Settings’
  4. select Note: If it doesn’t display… ‘Change Basic Configuration’ to a different number….
  5. Press Alt-C (‘Change Settings’)
  6. Change IRQ value to 05
  7.
  8. Select   2. Press – Properties – Resources
  3. ; deselect ‘Use Automatic Settings’
  4. select Note: If it doesn’t display… ‘Change Basic Configuration’ to a different number….
  5. Press Alt-C (‘Change Settings’)
  6. Change IRQ value to 07
  7.
  8. Select [color=red:1ftfntqa][u:1ftfntqa][b:1ftfntqa]Download Display Drivers[/b:1ftfntqa][/u:1ftfntqa][/color:1ftfntqa][/url:1ftfntqa]

Installing the Touch Screen Drivers
[color=red:1ftfntqa][u:1ftfntqa][b:1ftfntqa]
Download Touch Screen Drivers[/b:1ftfntqa][/u:1ftfntqa][/color:1ftfntqa]

  1. Unzip the touch screen driver file into a temporary directory
  2. Control Panel – Add New Hardware – – – – – (drive and path of temporary directory) – –
  3. Ignore Startup Log message
  4. Shutdown and restart system
  5. Go to button – – – – – O.K. (Accept params)
  6. (At Banner Page) Start – Programs – DOS Prompt
  7. cdTouchw95
  8. type
  9. ‘Export Completed Successfully’
  10.
  11. Change IRQ to 11
  12. Change IO Address to 824 (equivalent of IO Base 338Hex in decimal)
  13. Change baud rate to 9600
  14.
  15. (imports new data)
  16.
  17. Shutdown and cold boot (power on and off the system)
  18. (System boots back into WIN ’95 Banner Page)
  19. (with keyboard) Programs – Touch Utilities – Configuration – Calibration
  20. Use a stylus to press the calibration buttons.
  21.

Related Documents

[color=red:1ftfntqa][u:1ftfntqa][b:1ftfntqa]Configuring Win95 Systems[/b:1ftfntqa][/u:1ftfntqa][/color:1ftfntqa][/url:1ftfntqa]

[color=red:1ftfntqa][u:1ftfntqa][b:1ftfntqa]Javelin2 CPU[/b:1ftfntqa][/u:1ftfntqa][/color:1ftfntqa][/url:1ftfntqa]

[color=red:1ftfntqa][u:1ftfntqa][b:1ftfntqa]Javelin LC CPU[/b:1ftfntqa][/u:1ftfntqa][/color:1ftfntqa][/url:1ftfntqa]

[color=red:1ftfntqa][u:1ftfntqa][b:1ftfntqa]Javelin Styling Guidelines[/b:1ftfntqa][/u:1ftfntqa][/color:1ftfntqa][/url:1ftfntqa]